To-Go Kits - Heritage Print Bowls

 

MB105 tribal bowl 04 crop

Products Used

Bisque
  • MB-105 Rice Bowl (3)
Color
  • SC-15 Tuxedo (2oz)
  • SC-16 Cotton Tail (2oz)
  • NT-CLR Clear Dipping Glaze (at studio, not in kit)
  • **Amount needed for To-Go Kits are in parentheses

Decorating Accessories

  • RB-144 #4 Soft Fan
  • RB-106 #6 Script Liner

Additional Materials

  • Sponge
  • Water
  • Paper
  • Scissors
  • Palette
  • Pencil
Designer: Elizabeth Carey
 

Instructions: 3 Designs

1. Begin with properly fired cone 04 bisque. Moisten a sponge and wipe bisque to remove any dust.

Bowl #1

  1. Using the Soft Fan with SC-16 Cotton Tail, apply 2 coats to the outside and bottom of the bowl. Allow glaze to dry between coats.
  2. Using the Soft Fan with SC-15 Tuxedo, apply 2 coats to the inside of the bowl. Allow glaze to dry between coats.
  3. Use the pencil to sketch the design on the outside of the bowl. Start by making a small vertical line at the top of the bowl. Then add circles and more vertical lines. You can do 1, 2 or 3 circles going down from the top line. The design will look the best if it’s not precise.
  4. Using the Script Liner with SC-15 Tuxedo, apply 2 coats to your design. It will look best if your lines are not uniform. Allow glaze to dry between coats.

Bowl #2

  1. Using the Soft Fan with SC-16 Cotton Tail, apply 2 coats to the entire bowl. Allow glaze to dry between coats.
  2. Use the pencil to sketch 2 horizontal lines at the top of the bowl and 2 at the bottom of the bowl. Between the 2 middle lines, sketch “arrows” going in 1 direction. They do not need to be perfectly spaced.
  3. Using the Script Liner with SC-15 Tuxedo, apply 2 coats to your design. It will look best if your lines are not uniform. Allow glaze to dry between coats.

Bowl # 3

  1. Using the Soft Fan with SC-16 Cotton Tail, apply 2 coats to the outside and inside of the bowl (not the bottom). Allow glaze to dry between coats.
  2. Cut 6 strips off of the paper. They should be around ¼” wide and long enough to reach from the top to the bottom of the bowl (pressed against the outside). Cut around 6 large triangles (1.5” on all sides) and 10 small triangles (3/4” on all sides).
  3. Take the pencil and mark 6 dots on the rim of the bowl. They should be equally spaced, but do not have to be exact.
  4. One by one, dip the strips of paper in water and press them onto the outside of the bowl (from the dot to the bottom of the bowl). Using the Soft Fan with SC-16 Cotton Tail, apply a thin coat over the paper strips.
  5. One by one, take the large triangles and dip them into the water. Press each of them at the top of the bowl, between 2 lines. Using the Soft Fan with SC-16 Cotton Tail, apply a thin coat over the paper triangles.
  6. Repeat Step 5 with the smaller triangles, placing them below the larger triangle.
  7. Using the Soft Fan with SC-15 Tuxedo, apply 2 coats over the outside and bottom of the bowl. Allow glaze to dry between coats. Remove the strips and triangles before the last coat is completely dry.

Final

  1. Dip into NT-CLR Clear Dipping glaze
  2. Fire to cone 06.
MB105 tribal bowl 05 crop  MB105 tribal bowl 06 crop  MB105 tribal bowl 07 crop  MB105 tribal bowl 01 crop 

custom-css-security