Cobalt Wash Dinnerware Set

Details
Last Updated: Friday, 17 October 2014 15:57

 

Products Used

Bisque
  • SB-104 Rimmed Salad Plate
  • SB-105 Rimmed Dinner Plate
  • SB-110 Dessert Bowl
  • SB-116 Flared Mug
Color
  • SW-131 Birch
  • SW-255 Gray Opal
  • SW-305 Colbalt Wash

Decorating Accessories

  • CB-604 #4 Soft Fan
  • BT-910 Synthetic Sponge

Additional Materials

  • Palette
  • Doily
  • Banding Wheel
Cobalt Wash Dinnerware set

Designer: Marcia Roullard
 

Instructions

  1. Begin with properly fired shelf cone 04 bisque. Moisten a clean sponge and wipe bisque to remove any dust.
    SB-104 Rimmed Salad Plate:
  2. Pour a small amount of SW-305 Cobalt Wash onto a pallet. Take the doily and lay it in the SW-305 Cobalt Wash to saturate. Remove excess glaze from the doily by pulling it between your fingers. Stretch out the doily so it is flat and lay it over the surface of SB-104 Rimmed Salad Plate. Lay a paper towel over the doily and press down with a dry BT-910 Synthetic Sponge to be sure the doily pattern is transferred onto SB-104 Rimmed Salad Plate. Remove the paper towel and doily and allow to dry. 
  3. Center SB-104 Rimmed Salad Plate on the banding wheel. Using CB-604 #4 Soft Fan, apply 2 coats of SW-305 Cobalt Wash to the rim of SB-104 Rimmed Salad Plate.
  4. Using CB-604 #4 Soft Fan, apply 3 coats of SW-255 Gray Opal to the front and back of SB-104 Rimmed Salad Plate, trying not to disturb the doily design or SW-305 Cobalt Wash painted rim. Allow glaze to dry completely between coats. Allow glaze to dry completely between coats.
  5. Using CB-604 #4 Soft Fan, apply 2 coats of SW-131 Birch over the SW-255 Gray Opal. Allow to dry.
    SB-105 Rimmed Dinner Plate:
  6. Center SB-105 Rimmed Dinner Plate on the banding wheel. Using CB-604 #4 Soft Fan, apply 2 coats of SW-305 Cobalt Wash to the rim of SB-105 Rimmed Dinner Plate.
  7. Using CB-604 #4 Soft Fan, apply 3 coats of SW-255 Gray Opal to the front and back of SB-105 Rimmed Dinner Plate, trying not to disturb the SW-305 Cobalt Wash painted rim. Allow glaze to dry completely between coats.
  8. Using CB-604 #4 Soft Fan, apply 2 coats of SW-131 Birch over the SW-255 Gray Opal. Allow to dry.
    SB-110 Dessert Bowl
  9. Center SB-110 Dessert Bowl on the banding wheel. Using CB-604 #4 Soft Fan, apply 2 coats of SW-305 Cobalt Wash to the rim of SB-110 Dessert Bowl.
  10. Using CB-604 #4 Soft Fan, apply 3 coats of SW-255 Gray Opal to the interior and exterior of SB-110 Dessert Bowl, trying not to disturb the SW-305 Cobalt Wash painted rim. Allow glaze to dry completely between coats.
  11. Using CB-604 #4 Soft Fan, apply 2 coats of SW-131 Birch over the SW-255 Gray Opal. Allow to dry.
    SB-116 Flared Mug
  12. Slightly thin SW-305 Coblat wash with water (3:1) and pour to coat the interior of SB-116 Flared Mug. Pour out the excess and use BT-910 Synthetic Sponge to wipe away any drips.
  13. Using CB-604 #4 Soft Fan, apply 2 coats of SW-305 Cobalt Wash to the rim and flared section as well as the top of the handle of SB-116 Flared Mug.
  14. Using CB-604 #4 Soft Fan, apply 3 coats of SW-255 Gray Opal to the exterior, bottom, and remainder of the handle of SB-116 Flared Mug, trying not to disturb the SW-305 Cobalt Wash painted rim or handle. Allow glaze to dry completely between coats.
  15. Using CB-604 #4 Soft Fan, apply 2 coats of SW-131 Birch over the SW-255 Gray Opal. Allow to dry.
    For all four pieces:
  16. Using a dampened BT-910 Synthetic Sponge, wipe the feet of each piece clean of any glaze. 
  17. Fire to witness cone 5/6.

custom-css-security